UltraCrete Sectional Tanks & Storage
The purpose of Tanks/Storage in agricultural farm is to provide usable fertiliser that can be later used on land to fertilise crops, from a wide range of unusable materials, including animal waste and hay washed off from dairies, barns and stables.
Here at UltraCrete, we provide precast Sectional Slurry Tank, Modular Sectional Slurry Store, Modular Tank Columns and beams, Sectional Effluent Tank & Transfer Channel to best suit your requirements, as well as installation advice and assistance.
Available Slurry Storage Products
Sectional Effluent Tank
Sectional effluent tanks are supplied in 1000 gallon sections, built up to store 5000 gallons. They
can have slatted or solid covers with a hatch panel for emptying.
Design Features
- 1000 gallon sections
- Quick and easy to install, maximum 5 high
- Flood floor with ready-mix concrete to seal the tank
- Sealant strips supplied, comply with SEPA requirements
- Knockout pockets for incoming pipes
- Half check joint system to form a secure joint
- Designed to current BS EN standard
- Incorporated lifting socket for installation with a designed and tested bracket available for an additional cost
- Certificated lifting devices
- Sectional lids, slatted or solid with a hatch for emptying
Uses for Big T slats
- Silage pits effluent storage
- Fuel fill point spillage collection area
| Tank Size | Length | Width | height | Volume |
|---|---|---|---|---|
|
1 Section tank |
2700 mm |
3500 m |
0.6m |
1000 gallon |
|
2 Section
tank |
2700 mm |
3500 mm |
1.2 m |
2000 gallon |
|
3 Section
tank |
2700 mm |
3500 mm |
1.8 m |
3000 gallon |
|
4 Section
tank |
2700 mm |
3500 mm |
2.4 m |
4000 gallon |
|
5 Section
tank |
2700 mm |
3500 mm |
3.0 m |
5000 gallon |
Design & Quality Assurance provisions
- Design certificates available for your building warrants
- Concrete design certificates supplied
- Concrete strength cube reports available upon request
Modular Sectional Slurry Store
Underground modular slurry store is quick and easy to install, units come in standard 4572mm (15ft) or 6096mm (20ft) panels to create your tank size. Single width or multiple width tanks with support columns and beams available. This system removes the need to shutter tanks and with careful planning and organised deliveries can be erected in days, a crane normally required. Sealant strips are supplied for the tongue and grooved joints, requiring pointing when finished.
Design Features
- Panel sections come in 4572mm (15ft) or 6096mm (20ft) lengths
- Tank depth is 2360mm
- Quick and easy to install with a mobile crane
- Flood floor with ready-mix concrete to seal the tank
- Sealant strips supplied, comply with SEPA requirements
- Tongue and groove joint system to form a secure joint
- Designed to current BS EN standard
- Incorporated lifting socket for installation with a designed and tested bracket available for an additional cost
- Certificated lifting devices
- Solway slats and passage slabs offer a full package for your tank
Uses for Big T slats
- Underground slurry store within your shed project
- Underground slurry store
| Tank Size | Length | Width | height | Volume |
|---|---|---|---|---|
|
1 100ftx-
10ft |
30.480 m |
3.048 m |
2.36 m |
220 M3 |
|
2 100ftx-
10ft |
30.480 m |
6.096 m |
2.36 m |
440 M3 |
|
3 100ftx-
10ft |
45.75 m |
3.048 m |
2.36 m |
330 M3 |
|
4 100ftx-
10ft |
45.75 m |
6.096 m |
2.36 m |
660 M3 |
|
5 100ftx-
10ft |
61.00 m |
4.000 m |
2.36 m |
573 M3 |
Design & Quality Assurance provisions
- Design certificates available for your building warrants
- Concrete design certificates supplied
- Concrete strength cube reports available upon request
- SEPA approved system
- Method statement for erection available
Modular Tank Columns & Beams
Sectional effluent tanks are supplied in 1000 gallon sections, built up to store 5000 gallons. They can have slatted or solid covers with a hatch panel for emptying.
Design Features
- Columns are 350 mm x 350 mm and easy to install
- Beams are 350 mm x 350 mm with slotted ends for connections
- Quick and easy to install
- Made to length to suit your project
- Designed to current BS EN standard
- Incorporated lifting socket for installation with a designed and tested bracket available for an additional cost
- Certificated lifting devices
Uses for Big T slats
- Modular multi row tanks
Design & Quality Assurance provisions
- Design certificates available for your building warrants
- Concrete design certificates supplied
- Concrete strength cube reports available upon request
- Method statement for erection available
Sectional Slurry Tanks
U channels 2000mm long to suit 2400mm and 3000mm slats. Easy to installed with a half check joint and hydrophilic sealer strip. A first and last down with end wall complete the tank, the widths compatible with Solway slats.
Design Features
- Tank sections come in 2.4 or 3 meter widths
- Tank depth is 2.5 meters
- Quick and easy to install with a mobile crane
- Sealant strips supplied, comply with SEPA requirements
- Half check joint system to form a secure joint
- Designed to current BS EN standard
- Incorporated lifting socket for installation with a designed and tested bracket available for an additional cost
- Certificated lifting devices
- Solway slats and passage slabs offer a full package for your tank
Uses for Big T slats
- Underground slurry store within your shed project
| Tank Size | Length | Width | height | Volume |
|---|---|---|---|---|
|
2.4 m Tank |
30 m |
2.4 m |
2.500 m |
180 M3 |
|
3 m Tank |
30 m |
3 m |
2.500 m |
225 M3 |
Design & Quality Assurance provisions
- Design certificates available for your building warrants
- Concrete design certificates supplied
- Concrete strength cube reports available upon request
- SEPA approved system
- Method statement for erection available
Sectional Slurry Transfer Channels
Slurry transfer channels offer a quick and simple system to install. Channels 2000 mm or 3000 mm standard lengths with bespoke lengths made to order. Units to turn 90 degrees and first and last down end walls available. Internal size 1000mm x 900mm deep external 1200mm x 1000mm compatible with diagonal or transverse slats.
Design Features
- Channel sections come as standard at 2 or 3 metre lengths
- Channel depth is 1000mm
- Quick and easy to install
- Sealant strips supplied, comply with SEPA requirements
- Half check joint system to form a secure joint
- Openings can be incorporated for turning direction and ends for a first or last down unit
- Designed to current BS EN standard
- Incorporated lifting socket for installation with a designed and certificated lifting devices
- Solway transverse or diagonal slats are suitable for slurry chanels
Uses for Big T slats
- Transfer of slurry from pit to tower
- Some cattle sheds are developed and use transfer channels to collect slurry and transfer it to the store
Design & Quality Assurance provisions
- Design certificates available for your building warrants
- Concrete design certificates supplied
- Concrete strength cube reports available upon request
- SEPA approved system
- Method statement for erection available